LED FLASHER WITH ONE TRANSISTOR



This is a unique flasher circuit employing a single driver transistor that takes its flash-rate from a flashing LED. The flasher within the photo is 3mm. An ordinary LED won't work. The flash rate can not be altered by the brightness of the high-bright white LED will be adjusted by altering the 1k resistor across the 100u electrolytic to 4k7 or 10k. The 1k resistor discharges the 100u in order that when the transistor activates, the charging current into the 100u illuminates the white

LED.
If a 10k discharge resistor is used, the 100u isn't absolutely discharged and therefore the LED doesn't flash as bright. All the components within the photo are within the same places as within the circuit diagram to make it simple to envision how the components are connected.

The circuit uses a flashing LED to flash a super-bright 20,000mcd white LED


Comments

Post a Comment

Popular posts from this blog

Build a 12V 7 2Ah SMF Battery Charger Circuit Diagram

Image
Build a 12V 7.2Ah SMF Battery Charger Circuit Diagram . The LM317 is an adjustable three-terminal positive-voltage regulator capable of supplying more than 1.5A over an output-voltage range of 1.25 V to 37 V. It is exceptionally easy to use and requires only two external resistors, R2’ and R2” (R2= R2’+ R2”) to set the output voltage. Furthermore, both line and load regulation is better than standard fixed regulators. In addition to having higher performance than fixed regulators, this device includes on-chip current limiting thermal overload protection, and safe-operating-area protection. All overload protection remains fully functional, even if the ADJUST terminal is disconnected. By connecting a fixed resistor, R1 the ADJUST and OUTPUT terminals, the LM317 can function as a precision current regulator. An optional output capacitor can be added to improve transient response. Schematic Diagram using LM317   The ADJUST terminal can be bypassed to achieve very high ripple-rejection ra
Keep reading

Full Power Mobile Phone Jammer Circuit Diagram

Image
Full Power Mobile Phone Jammer Circuit Diagram .To day if we are talking about expert Cell phone Jammers we are conversing about this schematic underneath. First off all you should be very very cautious how to use this apparatus. Its completely illegal and so the reason. I post this Circuit is only for educational and testing causes. This type of apparatus is being utilised by security for VIPS, particularly at their limousines to avoid blasting device initiating while the vehicle passes from the goal cell phone-bomb. Off course there are those who use it to make a antic or to make the persons crazy in the rectangle block you are. The power of the jammer is currently sufficient to do your thing, but certainly you can place a 30W linear power amp at the RF output and impede a much wider locality. So, Be pleasant individual with that and recall that there are people who may need desperately to obtain or make a call and one of them could be you! And if you can't oppose of functio
Keep reading

On line Ladder Program Editing for RSLogix 500

Image
On line Ladder Program Editing for RSLogix 500 There are five basic steps in performing an edit on line.   1)   Start Edits, 2)   Make Changes, 3)   Accept edits, 4)   Test Edits, and 5) Assemble edits.   Although these steps seem very simple there are a few rules to watch out for.   You cannot expand or create a data table on line in the SLC, and you must be in program mode (or off line) to expand a data table on line in the PLC-5.   You cannot make an on line edit if the key switch is in Run Mode.   In the PLC-5, if backplane switch 8 is on, you cannot make an on line edit.     You do not need to perform an on line edit to directly change a value in the data table such as the preset of a timer or counter.   If the processor is in program mode, you do not need to test and assemble after accepting.   If the processor is in program mode, and a rung is deleted, there is no warning. Let's walk through the 5 step procedure: Look at the rung below.   Our objective is to transfer contro
Keep reading